MW Series

Universal Automatic Washer – MW-Series (Drum Washing, Pail Washing, Printing Press Component Washing, Parts Washing)

Universal Automatic Washer

The MW washers are designed to wash a wide variety of containers ranging from drums, 5 gallon pails, cans and an assortment of items to printing press components, in both solvent and aqueous applications.

The containers and/or parts are placed in a series of pre-designed cart configurations, which are then inserted in an enclosed wash chamber. Wash nozzles are located so as to wash both the interior and (optionally) exterior surfaces. A wash, pause and rinse cycle is automatically executed under the control of a programmable logic controller (PLC).

The wash cycle re circulates the solvent (or water) from a dirty solvent tank. The rinse cycle can either re circulate to a clean solvent tank, or draw from a clean solvent source and discharged to the dirty solvent tanks.

Printing Press Component WashersStandard Features and Options:
    • Stainless Steel interior and exterior
    • Non sparking aluminum grated floor
    • Internal gradient sump with level sensors
    • Hinged door with view window with safety switch
    • Vapor tight seals to control fugitive VOC emissions
    • NEMA 4 electrical components
    • Air, Nitrogen or CO2 purge valve
    • Exhaust port
    • High pressure pump and valves to 350 PSI @ 50 gpm
    • Rinse pump and valves
    • Scavenger pump and valves Printing Press Component Washers
    • Microprocessor Controller (PLC) in NEMA 4X Enclosure
    • Operator terminal with touch screen display
    • Pre-wired for field installation
    • Nozzle assemblies and pump (to 350 psi @ 50gpm) to wash exterior surfaces
    • Air Purge for NEMA 4X Enclosure for Explosion Rating (includes all wiring)
    • Exhaust fan with Class 1, Division 1 motor and non-sparking impeller with stainless steel internal ducting
    • Visual status indicator light system (PLC controlled)
    • Refrigerated vapor condenser to -40 degrees F for VOC control
    • Blow-out panel (to be ducted to an outside area)
    • Drying and vapor recovery cycles for alternative solvents

All MW-Series washers utilize a Closed Loop System ConfigurationClick here to read more about it.

 Drum wash cart assembly (for 3 drums) includes 3 wash nozzles

Pail wash cart assembly for (12) 5 gallon pails or (9) 10 gallon pails (not shown)
   
Wash cart for printing press components
 Printing Press Parts Washer  Printing Parts Washer
Printing Press Parts Washer Printing Parts Washer

A Real Customer Testimonial – “I have been involved with press parts washing for over 20 years. I have witnessed parts being cleaned in Renzmann Top Loads, Renzmann Model 300s, PRI SWS-300s, PRI SWS-400s, SRS MW-200s, SRS MW-1000s and SRS MW-1500s washers.

They used anything from Alcohols, Acetates, MEK, Toluene, HCS, H-02, MPC and MPC-1. I can honestly say that the SRS wash systems wash better due to the high pressure spray and the primary cleaning from their carts.

I witnessed an SRS MW-200 washer using the new SRS alternative solvent RIS 4563-A formula and was blown away. These parts are from a Gravure press and sat for 6 days while the washer was being installed. The total cleaning cycle was set at 45 minutes. That includes wash, rinse, dry and VOC recovery.”

Printing Parts Washer

Before

 Printing Parts washer

After


[easy_media_download url=”https://srsde.com/wp-content/uploads/2019/11/Multi-Washer.pdf” text=” MW- Series-Brochure-PDF” color=”blue_three”]
Bookmark the permalink.